Posted on September 24, 2020 by Jeff -
Wattage: 1w~90w
Features
- Assemble on the main PCB of the system
- Miniature encapsulated type
- No load power consumption <0.075W~0.1W
- Working temperature: -30~+85°C by models
- Comply with EN55022 class B without any additional components
- Various styles: PIN, SMD, Screw terminal style
Posted on September 22, 2020 by Jeff -
- Versatile miniature snap switch
- High level of repeat accuracy & contact stability
- Switching current 0.1 to 21 A at 250 VAC
- Wide variety of auxiliary actuators and terminal options
- Housing material PA 6 (T85 versions, colour black*) & PET (T125 & T150 versions, colour beige)
- Fulfills requirements of IEC 603351: GWFI at 850 °C, GWIT at 775 °C & GWT 750 °C
- Ambient temperature -40 to max. +150 °C
- Approved according to IEC 61058-1 / UL 61058-1 (T85 versions) & IEC 61058 and UL 1054 (T125 & T150 versions)
- Cadmium-free contact materials
- Halogen-free plastic material (T85 versions)
- Degree of protection IP40
Click here for a datasheet.
Posted on September 22, 2020 by Jeff -
Has two Hall Effect sensors; one detects the speed and the other detects the direction of movement of gear teeth. The outputs are open collector transistors. The speed output goes high (on) when sensing the leading edge of a tooth and low (off) on the trailing edge of the tooth when run against a standard target. The direction of movement is latched on the leading edge of the speed sensor; the direction output goes high for clockwise rotation and low for counterclockwise rotation. The state of the direction output always leads to the rising edge of the speed output.
Features
- Separate digital outputs for speed and direction
- From near zero speed up to 15 kHz sensing capability
- Plastic flange-mount sensor rated to 125 ⁰C
- RoHS compliant
- IP67
- Typical air gap of 1.5 mm (0.06”)*
Applications
- Wheel speed and direction
- Hoist speed and direction
- Transmission speed and direction
- Industrial feedback and control
Click here for a datasheet.
Posted on September 22, 2020 by Jeff -
Employs a Hall Effect digital vane sensor and a permanent magnet in two small towers, separated by a 3.4 mm (0.135”) air gap. The output switches when a ferrous target passes between the towers. Typical targets are linear or rotary vanes using a square saw tooth or an open slot in a solid disk or band.
Features
- Mechanically interchangeable with typical slotted optical switches
- Robust, high-speed sensing in dirty/dusty environments
- No mechanical contacts to wear out
- Open collector (sinking or NPN) output can be used with bipolar or CMOS logic circuits with a suitable pull-up resistor
- RoHS compliant
Applications
- Door/gate position control
- Exercise equipment
- Printers
Click here for a datasheet.
Posted on September 22, 2020 by Jeff -
- Robust standard switch for industrial applications
- 3 current ratings, up to 25 A
- Wide variety of auxiliary actuators available
- 3 terminal types (optional screw terminals available)
- 3 contact configurations
- High-temperature 150 °C (200 °C on request)
- Long-life coil spring mechanism
Click here for a datasheet.
Posted on September 22, 2020 by Jeff -
- IP67 subminiature switch with high repeat accuracy
- Switching Current 0.1 A to 10 A AC (model dependent)
- Wide variety of auxiliary actuators
- Actuators can also be retrofitted
- High contact stability due to specific contact materials
- Ambient temperature -40 to max. +120 °C
- Mechanical life min. 1,000,000 operations
- Approved according to EN 61058 and UL 1054
- Silicon-free version available
Click here for a datasheet.
Posted on September 22, 2020 by Jeff -
Noncontact, intrinsically linear contact angle position sensors with two independent outputs. The sensors operate through the use of Hall Effect technology with magnetic fields generated by permanent magnets. They provide a linear change in voltage output (ratiometric to the input voltage) corresponding to an angular rotation of the input shaft.
Features
- Angular position sensor with high tolerance for misalignment
- Noncontact angular position sensing and full 360° rotation
- Dual independent (redundant) outputs assure high reliability
- Custom programming available for angle range, slope, PWM contact factory
- No mechanical interface means no parts to wear out or jam
- Comes with 18 AWG 305 mm (12”) wire leads
- RoHS Compliant
- IP68*
- Maximum air gap of 5.5 mm (0.22”)
Applications
- Implement (forklift, agricultural trailer hitch, etc.) position sensing
- Steer, throttle by wire
- Gear selection
- Zero-contact encoder alternative
- Replacement for smart bearings
- Outboard trim sensing
Click here for a datasheet.
Posted on September 22, 2020 by Jeff -
Noncontact, intrinsically linear contact angle position sensors. The sensors operate through the use of Hall Effect technology with magnetic fields generated by permanent magnets. They provide a linear change in voltage output (ratiometric to the input voltage) corresponding to an angular rotation of the input shaft.
Features
- Angular position sensor with high tolerance for misalignment
- Noncontact angular position sensing and full 360° rotation
- Custom programming available for angle range, slope, PWM output, and custom magnets – contact factory
- No mechanical interface means no parts to wear out or jam
- Available with Delphi connector or 12” (305 mm) wire leads
- RoHS compliant
- IP67
- Maximum air gap of 5.5 mm (0.22”)
Applications
- Implement (forklift, agricultural trailer hitch, etc.) position sensing
- Steer, throttle by wire
- Gear selection
- Zero-contact encoder alternative
- Replacement for smart bearings
- Outboard trim sensing
Click here for a datasheet.
Posted on September 22, 2020 by Jeff -
- Single-pole panel mount pushbutton switch
- Momentary, Push-Pull (reset), and Cheat Interlock versions
- Long-life coil spring, snap-action mechanism
- Agency-approved extended-life versions available
- VDE approval available on select models (F Series)
- Snap-in panel mounting
Click here for a datasheet.
Posted on September 1, 2020 by Jeff -
Rated Input: AC90 – 264V 1Φ
Rated Output Wattage: 500W
Rated Output Voltage: 12V,15V,24V,30V,48V,56V
Features
- Wattage 500W max
- High Power density: 24.1W/inch3
- High efficiency 92% typ (Input Voltage 230V, Output Voltage 24V)
- Conduction cooling
- 3x 5standard footprint
- Fits 1U applications
- Industrial and Medical safety approvals
- Low leakage current
- With Remote On/Off (Optional)
- With AUX1 (12V) , AUX2 (5V) (Optional)
- No minimum load is required
Recent Comments